1.Quote According Sample or 2D/3D drawing or Picture with detailed information , If the part some design is not good , we will give suggestion and solutions to customer           ↓ 2.Discussion Mold material, cavity number, price, runner, payment, etc.           ↓ 3.Approved Order confirmed           ↓ 4. Advance Pay 50% by T/T           ↓ 5.Product Design Checking. We will send 2D and 3D part drawing and PPT file for customer check           ↓                    5.Mould Design According the Approved Part drawing , we will make the mold design and send to customer confirm           ↓ 6.Mold Steel Material and Component Prepare After drawing confirmed , we will start to prepare the steel material and standard components           ↓ 7.Mold Processing Send detailed reports with pictures to customer each week           ↓ 8.Mold Testing Send Test samples with report to customer           ↓ 9. Mold Modification According to customer's feedback           ↓  10.Balance settlement 50% by T/T after the customer approved the test sample and mould quality.           ↓  11.Packing and Delivery Each Mold will be packing with some damageable spare parts , and send detailed pictures to customer  Q/C Inspect Moulds: 1.Mould Material Q/C - Mould Steel Checking(Hardness, Crack ,Blow hole material defects ) - Mould Standard Spare Parts Checking(hardness, size, flaw checking) 2. Mould Machining Process Q/C - Design checking (Part design, mould design,Including 2D drawing and 3D drawing) - Each part of mould's size checking after machining according to 2D drawing - Mold Test (check mould running conditions and T1 samples) 3.Make sure to follow and checking each points of customer's request before shipment
Living garbage disposal equipment
With the development of increasingly urbanization , the amount of garbage increased geometrically. Incineration method gradually lost the market since the dioxin and toxic produced by incineration causing irreversible effects on the environment, and for landfill, some garbage is difficult to degrade, which even takes hundreds of years, we cannot afford this even though China has a vast territory, because land is a valuable non renewable resources.
After continuous efforts, Shangqiu Jinpeng industrial Co., Ltd developed a special biomass pyrolysis equipment for domestic waste treatment. After treatment by the equipment, can get about 20% of the oil profits from domestic waste, and in the process, through the low temperature anaerobic biomass pyrolysis of domestic waste harmless treatment, to ensure environmental health.
Flow chart for living garbage disposal equipment
Living garbage disposal equipment has two system:
1. Garbage Sorting System
The equipment is applied to separate organic waste and inorganic waste from large-size refuse and processing them separately.
2. Biomass Pyrolysis Equipment
2.1 The combustible waste after sorting and shredding such as life rubber, plastics and knitted fabrics is conveyed into the low-temperature and anaerobic biomass decomposing processor. Through catalyzing and heating, oil gas is produced and then condensed into oil mixture by condenser. The remaining that can`t be liquefied is processed through gas purification system and then used to generate electricity by gas generator. The smoke after burning goes into smoke scrubbers so as to remove acid gas and dust, and then is discharged through chimney when it reaches relevant environmental standards. The residue from biomass decomposition is conveyed into carbon black collecting tanks through sealed screw, without any pollution.
2.2 The technical parameter of Biomass Pyrolysis Equipment
NO.
ITEM
Technical Parameter
1
Suitable Raw Materials
Small pieces of Waste tire, rubber, waste plastic≤5cm
2
Operating Mode
Fully Continuous Operation
3
Structure
Horizontal Type Revolve
4
Loading and discharging
Fully automatic feeding and discharging under high temperature at same time
5
Capacity(24h)
20-40Mt
6
Work Pressure
Slightly Negative Pressure
7
Oil Yield of tyres
40%-45%
8
Reactor Rotational Speed
1R/M
9
Installation Power
110kw/h
10
Cooling Method
Cycle water
11
Type of Drive
Sprocket Wheel
12
Heating Method
Direct
13
Noise dB(A)
≤85
14
Main Reactor Weight (MT)
About 20Mt
15
Total Weight(MT)
About 45Mt
16
Installation Space Required
60m*20m
17
Manpower
2/shift
18
Shipment
5*40HQ
19
Delivery time
≤70Days
Living Garbage Processing Equipment Municipal Waste Recycling,Garbage Recycling Machine,Waste To Energy Shangqiu Jinpeng Industrial Co., Ltd. , https://www.recyclings.nl
Cavity/Core Material
P20,718,2738,H13,DIN1,2311 or as customer quested
Product Raw Material
PP
Cacity
Multi Cavity
Cycle Time
20S
Runner System
Hot runner,Cold runner
Finish
Good Polishing
Mold Guarantee
500,000 Shots
Mould Standard
HASCO,DME,or by requested etc.
Software
CAD,Pro-E,UG,Solidwork
Tolerance
± 0.02mm
Main Technique
Milling, Grinding, CNC , Engraving ,EDM, Wire-cutting etc.
Packing
Wooden Canse
Payment Terms
50% deposit by T/T,balance against B/L copy
Port
Ningbo Port
Lead Time
40-45 days
Plastic Injection Mould for Laundry Basket Export to Canada
Model NO.: YX-1850
Design Software: Pro-E
Installation: Mobile
Customized: Customized
Cavity: One
Matrial: P20
Transport Package: Wooden Packing
Specification: customized
Origin: China
HS Code: 8481719090